施耐德变频器ATV21快速启动手册（英文）.pdf施耐德变频器ATV21快速启动手册（英文）pdf,

文件名称: 施耐德变频器ATV21快速启动手册（英文）.pdf

所属分类: 其它

开发工具:

文件大小: 1mb

下载次数: 0

上传时间: 2019-10-08

提供者: weixin_********

下载 (1mb)

不能下载？报告错误

详细说明：施耐德变频器ATV21快速启动手册（英文）pdf,施耐德变频器ATV21快速启动手册（英文）CSet motor parameters(continued Menu Code Description Factory setting stomer ttin F Set F 4oU [Auto-tuning drive]parameter to 2. The drive EXTENDED MENU F4DD displays R E n I, the message disappears after a few seconds Auto-Tunning for uL u, uL, F4 /S and F4 /7 AA DANGER ▲ WARNING HAZARD OF ELECTRIC SHOCK OR ARC FLASH DAMAGED DRIVE EQUIPMENT During auto-tuning the motor operates at rated current It is essential that the following parameters uLu uL F4 /5 and F 4/7 are correctly configured before starting autotuning Do not service the motor during auto-tuning When one or more of these parameters have been changed after auto tuning has been performed, F 40n will return D and the procedure will have to be repeated Failure to follow these instructions will result in death or Failure to follow these instructions can result in death serious injury, or equipment damage. 8 Set basic parameters Menu Description Factory setting Customer setting AU/ Auto ramp adaptation 0 Disabled Enabled- ALL and dE匚 2 Enabled (ALL only) ALL Acceleration time 1 Acceleration ramp and the time s) ATV21≤15KW=10s AUF Deceleration time 1: ATV21>18KW=30s dec QUICK MENU Deceleration ramp and the time(s) LL Motor frequency at minimum reference (hz) High L sp 5囗 Motor frequency at maximum reference(Hz) 上Hr Motor rated current overload setting Motor Rated Current Overload Setting (%). Switching Frequency Level: (kHz) EXTENDED F 30D Increasing the switching frequency may reduce audible motor noise 日to|d MENU See the derating curves in the ATv21 Installation Manual ⑨9 Set control choice (91 [REMOTE configuration] 92 LLOCAL configuration Parameters factory settings 2-wire control Menu Code setting [od control terminal remote mode start/stop contro logic inputs RUN FI forward run F logic input function command EXTENDED MENU F112 reverse run R logic input function command 3-wirecontrol Menu g nod control terminal remote mode start/stop controd logic inputs STOP UN F11 RESET F logic input function start forward F EXTENDED R logic input function stop input MENU RES logic input function start reverse 10 Start the motor www.schneider-electric.com 3/4 S1A73479-10/2010 Menus structure Run Programming Monitoring mode mode mode MODE AUF Submenu Quick menu ⊙+↑Q ATV21 Submenu drive User Parameters Auto ramp adaptation Drive run time Power Up Submenu ⊙↓↑ Extended Menu Acceleration time 1 Drive service alarm Preset speed 7...1 Past fault HEr Deceleration time 1 nt n Motor Overload Characteristics Low speed adnOrmal state ( 上Hr Motor rated current ODE Communication overload setting High speed counter Motor Voltage Boost LHc Motor rated current 5口 Motor speed d setting Motor control mode Drive rated Analog output scaling output current Motor rated vol Accumulated output Motor control mode ⊙ ↑ power consumption ⑨↓↑∞ Accumulated input Motor rated trequency ↑ o Power consumption Low speed PID computed Motor rated voltage H7 speed reference High spccd PID feedback MODE (1 Direction everse direction ,↑ Maximum frequency JEO Memory version Deceleration time 1 D CPU 2 version VOD RC[ Acceleration time 1 CPU 1 version Local mode motor rotation direction command Relay output map Parameter reset Logic input map Analog output scali oiL Motor operating Analog output function selection 75 Output pot F门a Remote mode primary speed reference source [nad remote mode start/stop control source drive load fact Macro programming toRque current Au/ Auto ramp adaptation Motor torque Submenu RU d otor voltage ine voltage Motor current Refer to the programming manual for comprehensive menu description Spccd reference Hz www.schneider-electric.com 4/4 S1A73479-10/2010

(系统自动生成,下载前可以参看下载内容)