[硬件开发] 蓝桥杯单片机矩阵按键程序.zip

说明：蓝桥杯单片机矩阵按键程序，用定时器和中断，放在While循环里面不断扫描即可，按一下只执行一次，不会影响数码管闪烁和其它程序的执行，非常的银杏，非常的好用。
<Supremelv> 上传 | 大小：169kb

[硬件开发] 蓝桥杯单片机霍尔传感器程序.zip

说明：蓝桥杯单片机霍尔传感器程序，用定时器和中断，只用一个定时器用来计数计时，不会影响数码管闪烁和其它程序的执行，非常的银杏，非常的好用。
<Supremelv> 上传 | 大小：194kb

[硬件开发] USB Type-C ECN - Electrical Requirements for LRD-based active cables

说明：Adds new section 6.6.5.4 to describe electrical requirements for redrived based active cables Adds new section Appendix G to describe the procedure to extract the pulse response from sampled data and calculating non-linearity noise of LRD based activ
<u012028275> 上传 | 大小：425kb

[硬件开发] USB Type-C ECN - E-Marked Cable shall only use Vconn

说明：All active cables except optically isolated active cables shall only be powered from Vconn unless V CONN is not present in which case they can be powered by V BUS . Added a timing requirement to Table 4-6 for the switch from V BUS to V CONN power.
<u012028275> 上传 | 大小：89kb

[硬件开发] USB Type-C ECN - Mated Connector SI requirements

说明：Clarify that the mated connector SI requirements apply to only the receptacle connector.
<u012028275> 上传 | 大小：108kb

[硬件开发] USB Type-C ECN - Section 6.6.5 USB4 Active Cable Electrical Requirements

说明：Adds new section 6.6.5 to describe electrical requirements for retimer based active cables
<u012028275> 上传 | 大小：419kb

[硬件开发] USB Type-C ECN - Timing for Ra removal and restoring Ra

说明：Provide specific timing for a cables, VPAs, and VPDs to remove and restore Ra. Create a new Ra management state machine to make the cable requirements clear. vVconnDisconnect minimum is increased to provide margin.
<u012028275> 上传 | 大小：172kb

[硬件开发] 基于FPGA的SD卡读写

说明：FPGA SD卡读写 FPGA SD Card Reader FPGA SD卡读写 FPGA SD Card Reader
<landongming1987> 上传 | 大小：11mb

[硬件开发] roboware-studio_1.0.2-1512004582_amd64

说明：ROS开发的软件roboware-studio_1.0.2-1512004582_amd64 ROS开发环境RoboWare Studio
<weixin_45160028> 上传 | 大小：74mb

[硬件开发] STM32-Bootloader

说明：STM32-Bootloader，包含外设初始化和反初始化。
<albertdiao> 上传 | 大小：156kb

[硬件开发] ADC/DAC应用设计宝典

说明：“ADC”Analog-to-Digital Converter的缩写，指模/数转换器或者模拟/数字转换器。真实世界的模拟信号，例如温度、压力、声音或者图像等，需要转换成更容易储存、处理和发射的数字形式。模/数转换器可以实现这个功能。
<u013607013> 上传 | 大小：1mb

[硬件开发] Signal Integrity and PCB layout considerations for DDR2-800 Mb/s and DDR3 Memori

说明：Signal Integrity and PCB layout considerations for DDR2-800 Mb/s and DDR3 Memories
<u013607013> 上传 | 大小：555kb